Takagi logo

Takagi Tankless Water Heater Expert Service

Expert Takagi tankless installation and service in San Francisco and Marin. Commercial-grade copper heat exchangers built to last.

Experienced Takagi Installer

Ocean-Side Performance & Coastal Durability

Hydroflow technicians are trained to install and service Takagi tankless water heaters. We understand the specific venting and gas line requirements for these units to ensure safe and efficient operation in San Francisco. We have extensive experience with Takagi installations particularly in neighborhoods like The Sunset and The Outer Richmond, where their exterior units thrive in coastal salt-air conditions. Takagi is one of our go-to brands for exterior coastal installations alongside A.O. Smith.

Takagi Models We Install:

  • T-H3 Series — high-efficiency condensing tankless, top-tier efficiency ratings
  • T-K4 Series — compact non-condensing models for smaller homes and tight spaces
  • T-D2 Series — high-demand units for larger residential and light commercial applications

Why Choose Takagi

Tankless-Only Since 1952 — Commercial-Grade Copper Heat Exchangers

Takagi has focused exclusively on tankless water heating since 1952, making them one of the most specialized tankless manufacturers in the world. That singular focus shows in their product quality — commercial-grade copper alloy heat exchangers that outlast competitors’ residential specs. For Bay Area coastal homes, Takagi’s exterior-rated units are particularly valuable. We install flush valves on all exterior Takagi units as standard practice, making annual descaling and maintenance straightforward.

Takagi Advantages:

  • Tankless-Only Focus — 70+ years solely on tankless technology, no distractions
  • Commercial-Grade Copper Alloy Heat Exchangers — higher durability than residential specs
  • Coastal Track Record — exterior units proven in salt-air environments near the ocean
  • Compact Wall-Mount Design — frees up garage floor space
  • Advanced Safety Systems — computer-controlled monitoring throughout operation

Takagi FAQ

What does Takagi Error Code 111 mean?

Code 111 is ‘Ignition Failure’. The heater isn’t lighting. This is often due to the gas supply being off, a dirty igniter rod, or insufficient gas pressure. Check that your gas valve is open and that other gas appliances in your home are working.

What is Takagi Error Code 121?

Code 121 indicates ‘Loss of Flame’. The unit lights but the flame goes out during operation. This can happen if the flame sensor is dirty (covered in carbon deposits) or if there are wind issues affecting the venting on exterior-mounted units. A technician can clean the sensor to resolve this.

What does Takagi Error Code 711 mean?

Code 711 is a serious error indicating a problem with the gas solenoid valve drive circuit or the control board. It often requires replacing the circuit board or gas valve assembly. Professional diagnosis is required — don’t attempt to reset repeatedly.

How do I clean the inlet filter on my Takagi?

Locate the inlet water filter where cold water enters the unit. Turn off the water supply, unscrew the small plug/filter housing, rinse it under running water to remove debris, and reinstall it. We include this in every annual maintenance visit.

What does Takagi Error Code 291 mean?

Code 291 is a ‘Flow Rate Issue’ — the unit isn’t detecting enough water flow to fire safely. Common causes include a clogged inlet filter, partially closed isolation valves, or scale buildup inside the heat exchanger restricting flow. Start by checking and cleaning the inlet water filter. If flow is still low, the heat exchanger likely needs descaling. Takagi’s copper alloy heat exchangers are more resistant to scale than stainless steel but still need periodic flushing, especially in Marin County’s hard water.

What does Takagi Error Code 200 mean?

Code 200 indicates ‘Overheating’ — the outlet water temperature exceeded safe limits. On exterior-mounted Takagi units, this can occur if the unit fires in direct sunlight without proper shading, if the flow rate drops below minimum while the burner is still running, or if there’s a scaling issue in the heat exchanger. Do not repeatedly reset — overheating can damage the copper heat exchanger. A technician needs to diagnose the root cause.

Schedule Your Takagi Service Today

Interior and coastal exterior Takagi installations, annual maintenance, and repair across San Francisco and Marin County.

Get an Estimate